Contact/FAQ ダウンロード


Catalog
Download

LS-R740 (WL)

LS-R740 (WL)

Air Leak Testers
Helium/Hydrogen
Leak Testers
Pressure
Flow
Peripherals
Others
Sound/Vibration
Analyzer
Cosmo Super Gel

Air Leak Tester for Small Sealed Parts　　LS-R740(WL)

This tester is ideal to test Water-proof components or finished products which require IP Protection Rating.The part to be tested is placed in a capsule and pressurized to measure the pressure change caused by leak flowing into the part.

Edge & Function

Easy-to-navigate and intuitive interface with simple menu configuration
Easy volume compensation when the tested part and the reference part have a volume difference
Influence of noise genarated in the test on the part can be compensated, reducing test time
User selectable multi-language capability: English, Japanese and Chinese
USB port for easy test data management
Closer placement fo sensor section to the target capsule

Spec

Spec

Differential Pressure Resolution 0.1 Pa
Display Range ±999.9Pa,(Accuracy guaranteed range±1000Pa)
Accuracy ±2.5% of rdg ±1Pa、50Pa or lower ±2Pa
Sensor Proof Pressure 5 MPa
Dislay Unit Test Pressure kPa，MPa
(Non SI Unit for overseas use kg/cm2, PSI, bar, mmHg,Others)
Leak Rate Pa, kPa, mL/s, mL/min, L/min, Pa・m3/s,
E-3 Pa・m3/s, Pa/s, Pa/min,＊Pa/s, ＊Pa/min
(Non SI Unit for overseas use mmH2O, mmHg, inH2O,Others)
K(Ve)
(Leak Coefficient)		 mL, L (Non SI Unit for overseas use  in3, ft3)
Leak Rate Display 4 digits,Sampling Rate 10 times/sec
Leak Limit ±999.99 max
Number of Channels 32ch(0～31)
Timer 999.9 secResolution 0.1 sec)
Power Source AC100～240V±10%, 50/60Hz,70VA max
Ambient Temperature 5～45 ℃
Humidity 80% RH or less / No dew condensation
Weight Controller: approx. 2.6kg, Pneumatic unit: approx. 11kg
Test Pressure Source Clean and dry air regulated to the test presssure
Source pressure must be sufficiently higher than the test pressure
Pilot Pressure Set by using the pilot pressure filter regulator installed
Range: 400 to 700kPa
Port Size Rc(PT)1/4: (Pressure source, WORK and MASTER ports), Pilot pressure source
CPU SH-2A　144MHz, DRAM8MB
RS-232C
(D-sub 9pin)		 ID2 Format Limit values as well as Large leak limit and Small leak limit are transmitted
L2 Format L-DET and S-DET test results are transmitted
Others Other 4 formats available
USB Port Test data Judgment, Leak, Test pressure, Channel #,　Time, etc
Test parameter Test parameters of all the settings screens
Calibration/ Maintenance Port M10 x 1.5 (O-ring seal)
Standard Accessories Test pressure regulator and filter,Pilot pressure filter regulator,Quick mounting brackets,Control I/O connector, Power cord, Inspection records,Operation manual,Traceability documents

Pnematic Circuit

LS-R740WL 空気回路図

 

Solenoid valves DL1 L-CHG L-BAL L-DET S-CHG DL2 S-BAL S-DET BLW EXH END
SV2
SV4
SV6

Classification

Classification

LS-R740WL- ①②③④

① Tank Type C100 Tank 100mL
② Test Pressure Low Pressure L Test pressure range  10 ～ 100 kPa
Medium Pressure M Test pressure range  50 ～ 700 kPa
Vacuum Pressure V Test pressure range  -5 ～ -100 kPa
③ Option Auto Leak Calibrator K1 ALC1
K4 ALC4
Nylon Filter housing RX02 Filter housing for the pilot pressure port is nylon
RX03 Filter housing for both the test pressure and pilot pressure port are nylon
DPS 10kPa, Resolution 1Pa D4 DPS Range:  ±10kPa,Display Range: ±10kPa,Minimum Display:  1Pa
NPT Fittings PX1 Connecting port thread is NPT
Panel Mount P The controller is designed to be panel-mounted
④ Cable Length Specified Unit-to-unit cable 3m S3 Standard
Unit-to-unit cable 5m S5 Option
Unit-to-unit cable 10m S10 Option


Appearance

Controller

Pneumatic Circuit Unit